We have stumbled on this article relating to Tools You Need to Install a New Bathtub below on the internet and reckoned it made good sense to write about it with you here.
Installing a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is conveniently available, the project can move easily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. Ensure you have certified yourself for the task and fit attempting it. Rather than working with a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This article will certainly assist you mount a brand-new bathtub in your washroom if you have currently gotten a new tub as well as do not need to transform the plan of your previous water pipes.
Your devices and material list should comprise the following:
Planning for the Setup
Firstly, the supporting structure provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing faucets can be quite troublesome because of the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the level reads level.
To mount taps, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and examine all joints and also new pipework for leaks and tighten them if essential. Fill the bath tub and also examine the overflow outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also securing around the tub must wait until the tub has been utilized at least once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the faucet in place with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in difficulties with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that article about A Step-by-Step Guide to Installing a Bathtub while doing research the internet. Sharing is caring. One never knows, you will be helping someone out. Thank you for your time. Visit us again soon.
Click Here To Read More